左右棋牌

Vaping Masters' Space!

Top Airflow—Wotofo Sapor RTA Review

Source:OriginalAuthor: Rita 562Like Issue Date:2016-07-19 18:07 Sort:Atomizers 󰀢Comments:0

ddb554eb74ff4d35876193952edc1d41.jpg

[Guide] The top airflow structure refers to the design of an atomizer that has air flow ports on the top and beneath the drip tip. When this method was first put forward it is seen as the assistant way of the bottom airflow, which could increase the volume of airflow and lower down the vapor’s temperature.


Since Joytech’s CUBIC first adopts the top airflow as its main air flow method, the structure has been widely applied to various RDAs. 


Recently, a large amount of RTAs emerge in the e-cig market, which has caught many people’s attention because of its special structure that could both store liquid and produce big vapor。 Wotofo has also launched its top airflow RTA—Sapor。 Then what is the experience of adopting top airflow to a RTA? Here I would like to share my experience about Wotofo Sapor RDTA。  

b091fc4742634281ab60961f63b54766.jpg

Sapor’s packaging adopts paper box, which is overall in black and with red patterns, being very striking to the eyes. The bottom is printed with the logo of Wotofo, and the color of the atomizer is marked on the upper right corner. 

f41413eda9af41bd9b9c4048c9c01316.jpg

Inside the box there is a Sapor atomizer and a standby glass tank。 On the bottom places the handbook, the guarantee card, the pre-made twin twisted coils, the cotton, the silica ring, the screws and a wrench。 


左右棋牌Sapor hasn’t adopted the traditional T shape wrench of Wotofo, instead it includes the Allen wrench into its packing this time, which is a pity for Wotofo’s new users。 The T shape wrench includes two regular Allen wrenches and a Phillips screwdriver, being very practical。 


Another special point is that Sapor has three pre-made trick coils for the users the give full play. 

27c2d7045dcc4e139c73d4283d479815.jpg

Sapor’s overall length from the tip to the bottom is less than 5cm, and even when the 510 connector is counted in, it is around 5。5cm, which is relatively small among like products。 The craftsmanship and material adoption of it are both in place。 It also possesses fair surface polish。 

The top airflow atomizers’ bottom structure is simpler and more uncoordinated with the top compared with traditional atomizers because of the abandon of the bottom airflow port. Sapor has its special design in this aspect— the base’s thickness is combined with that of the inner evaporation tank. 

ca70a71b90ec45f78f0b4c3027ff842b.jpg

(From the left to the right are:the top tip, the top cap, the adjusting ring, the tank top cap, the glass tank, the evaporation tank, the base。)


The parts of Sapor are a little bit redundant in quantity。 Most of the parts service for the top airflow structure。 Considering the problem of cleaning and maintenance, the tank and top cap are separately designed, which is superficially complex but actually convenient。 

1258a4945d5c4a61b3989f8d956b990f.jpg

Sapor’s 510 drip tip is exquisitely designed。 There is an extra “coat” around it, avoiding the negative effect that may be brought by overheating。 

f105763f72a34c33af3b28ea2ae998f8.jpg

The top cap part is connected to the drip tip by one side, and to the evaporation cap through the threads inside. 

c15948a9884c481aa2e97515bca12611.jpg

The cap combines the function of the liquid filling port, the vape flow tube, and the air flow port. The inner space of the tube is divided into the air inlet part and the outlet part, being connected to the inner tank. 

8d9364c533184436aabccbada0488e85.jpg

The evaporation tank is concave with six holes。 The air flows from the outer layer into the inner tank through the holes and exhausts through the tube in the center。 

d7e7a4fa1dad4c97b1219940e19cf8aa.jpg

Sapor’s base also adopts the classical dual-electrode and four-hole structure. Thanks to the top airflow structure, the size and depth of the liquid flow groove is large enough, which enhances the liquid flow performance. Meanwhile, the atomizer is more compatible with trick coils and low-resistance coils. 


However, Sapor’s fixing ring that has threads may clip the cotton fiber and thus affect the process of operating. 


There are two round groove signs on the side face of the base, which could help to correctly install the evaporation tank。 

b8b1b4fd36544f1399076f8151152e40.jpg

The three twin twisted coils send by Sapor are a little bit confusing, because there is no single-coil kit included at all.


I use the Kanthal A1 heating coil to make coils in my use experience, after all the pre-made coils will inevitably be replaced. Considering the structure and liquid flow ability of Sapor, I wind the 22Awg coils 6 circles under the diameter of 3mm, which is relatively common to see. 

be66367f206446a79cdd46666d38ccef.jpg

Install and fix the coils, and adjust the heating to an even status, then pass through proper amount of cotton after the coils cool down. 

f6dbaa58dda14c24bf342af4232b5482.jpg

Sapor adopts the fixing ring to fix the cotton, therefore we should adjust the cotton before soak and burn the cotton to relive the peculiar smell. While installing the ring, pay attention to align the threads with it, which will be affected by the abundant fibers. 


Screw tightly the fixing ring, then cut the abundant cotton outside the liquid flow groove to keep a moderate amount of cotton inside。 To provide convenience for the liquid apply, you could scatter the cotton after that。 

82a7feb90b4a439c9fc32fd2602e1535.jpg

Minikin 1.5’ s actual resistance is 0.2Ω, which has a fair vapor effect under the power of 60W, being somehow inferior to like RDAs. 

3e93d824b84340378ee00aad3d506143.jpg

Actual Experience:

A。 Vape Volume

Under the same data, Sapor performs worse than regular RDAs because of its RTA structure and the design of the base, which is the common character of most RTAs。


B. Flavor

Sapor’s flavor is accurate and has the sense of depth, but it is not rich enough, which may be caused by the top airflow design。 However its flavor is better than regular RDAs, but lighter than Lemo 3。 


C. Ease of Use

Although Sapor’s parts is relatively too many, it will not affect your everyday use at all. The dual-electrode and four-hole structure is convenient for installing coils, and the abandon of the bottom airflow pots leave more space for the bottom liquid flow groove, making it more suitable for making big-diameter coils. But the fixing ring with the design of threads may cause it difficult to align accurately.


左右棋牌D. Reliability and Others

Sapor’s top airflow endows it with high reliability。 The problem of liquid leaking will not happen under normal use。 But the atomizer could not be fixed tightly on the box, which may owe to its relative loose inner structure and adjusting ring。 

bd11a7647df745bc83f71f62312d3295.jpg

Summary:  

Wotofo’s Sapor RTA is a kind of big-vapor RTA, and its most important feature is the top air flow design. Besides, its small size and fair craftsmanship and material adoption are also the strength. Though it have shortcomings in some details, it should still be regarded as a distinctive RTA which performs well in both the vapor volume and flavor.

49b7b5dd8457420aa15064b0bd92eaa5.jpg

Would you like:RTA

󰄲TOP COMMENTS

󰀢Leave a Comment
豪利棋牌 人人棋牌 金贝棋牌 友趣棋牌 卡卡棋牌 陕西棋牌 奇乐棋牌 大菠萝棋牌 人气棋牌 豪利棋牌